EI-OT 16 Kanal Relais PRO 7,5V-26V Spannungsversorgung herstellen
- EI-OT 16 Kanal PRO Relais Platine um das MP1584 Modul erweitern
- 5V Brücke zur Relais Modul Spannungsversorgung setzen
- Zusammensetzen der Steuerungs- und der 16 Kanal Relais-Platine
- 7,5-26V Spannungsversorgung herstellen
Inbetriebnahme des 16 Kanal Pro Relais Modul mit einer Spannungsversorgung von 7,5-26V
EI-OT 16 Channel PRO Relays Module 7.5-26V MP1584 Power Supply |
Relais Modul 7,5-26V Spannungsversorgung
Um das EI-OT 16 Kanal Relais mit höheren Spannungen (größer 5V) zu betreiben, muss die Steuerungsplatine zusätzlich mit einem MP1584EN 5V Spannungskonverter erweitert werden. Die EI-OT 16 Kanal Relais PRO Platine ist bereits vorbereitet und erlaub eine einfache Bestückung des MP1584EN Spannungskonverter. Wichtig, bei der Platzierung des MP1584EN muss auf die richtige Positionierung geachtet werden
gemäß Darstellung auf der Platine. Die Bestückung des Spannungskonverters Schritt für Schritt:
Die Spannungsversorgung über den MP1584 Konverter ist fertiggestellt. Der MP1584 konvertiert Eingangsspannungen von 7,5V bis 26V auf 5V. Die Spannungsversorgung erfolgt nun zentral (auch für das 5V 16 Kanal Relais Modul / blaue Platine) über die 2-polige KF350 Schraubklemme der Steuerungsplatine.
|
Relays Module 7.5-26V Power Supply
In case of EI-OT 16 Chanel PRO Relays Module is operated with power supply between 7.5V and 26V a MP1584EN Voltage Converter is required. The 16 Channel Relays PRO Module its prepared for easy assembling of the MP1584EN. Important, please take care of correct orientation of the MP1584 Module, in detail
just follow MP1584 figure on PCB. MP1584EN Voltage Converter Module assembling step by step:
The 16 Channel Relays Module PRO controller Board supports now central power supply from 7.5V up to 26V thru 2-pole Screw Connector. |
5V Standard 16 Channel Relays Module Power Supply |
Relais Spannungsversorgung
Die 5V Spannungsversorgung des EI-OT 16 Kanal PRO Relais erfolgt nun zentral über die 2 -polige Anschlusklemme der Steuerungsplatine (schwarze Platine). Da aber 5V Relais Module sich in der Spannungsversorgung unterscheiden können, muss die Versorgungsspannung der Relais auf der Unterseite der EI-OT 16 Kanal Relais Platine entsprechend gebrückt werden. Es sind 2 Versionen von 5V 16 Kanal Relais Modulen verfügbar Version1: Hier muss auf der Unterseite der EI-OT 16 Kanal Standard Relais Platine
Version2: Hier muss auf der Unterseite der EI-OT 16 Kanal Standard Relais Platine
Die 5V Spannungsversorgung durch das Controller Platine ist fertiggestellt. |
Relays Power Supply
The Power Supply of the Relays is supported thru the 2-pole Screw Connector of the Controller Board (black Board). The power supply of 5V Standard Relays Module could be different. In this regard the Relais Voltage Supply must be connected on backside of EI-OT 16 Channel Module PCB. There are 2 types of 5V 16 Channel Standard Relays Module available Version1: please connect 5V < 2 Pad
Version2: please connect GND > 1 Pad The Power Supply thru the Controller Board is finished. |
Assembling EI-OT PCB and Standard 16 Channel PRO Relays Module |
Relais Modul verbinden
Sobald die Platine fertig bestückt wurde und die notwendigen Brücken gesetzt wurden, können Steuerungsplatine und das 16 Kanal PRO Relais Modul zusammengesetzt werden.
|
Relays Module Connection
Soon as the PCB is assembled, the controller PCB and the 16 Channel Relays Module can be assembled.
|
EI-OT 16 Channel PRO Relays Module 7.5-26V power supply |
Spannungsversorgung
Die Spannungsversorgung erfolgt mittels KF350 Schraubklemme der Controller Platine, Anschluss
Die Spannungsversorgung auf keinen Fall an die 2-polig Anschlussklemme der blauen Relais Platine anschliessen! Als Netzteil eignen sich typische
Die Spannungsquelle sollte mindestens 1500mA bereitstellen um ausreichende Leistung für die Relaisspulen bereitzustellen. |
Power Supply
Connect Power Supply thru KF350 Screw Connector of the controller board
Don't connect Power Supply to 2-pole Screw Connector of blue Relays Module Board! Typical Power Supplies are
The minimum Current should be 1500mA. |